Thanks, I will get onto this first thing in the morning. Will report back how I get on. 

so uhm...
How do I reduce the overall brightness in texmex, and how should I go about removing fullbright spots in my textures?
Thanks again. 

in lost chapters the corpses sank into the ground with a delay. 

I'm editing the console and HUD graphics. All is typically going well except ATTN: METLSLIME! - your Fitzquake (0.75 and 0.80) crashes since my most recent GUI updates. However, Winquake does not crash! Usually the crash can be attributed to a file that is too large/doesn't meet the right size - but this is not the case, and all the graphics are the corret palette too. What say you? 

While Winquake does not crash immediately after launch (like FitzQuake), it does crash once I start a map and says: "Double Quake Error - Draw_TransPic: bad coordinates" -- whereas when FQ crashes it just gives a cryptic "This program has performed an error" or somesuch. 

Unfortunately, it doesn't work with Fitzquake.

I tried DarkPlaces and at least saw the effect, which is quite cool. Thanks for trying.


Bambuz: I just checked Lost Chapters and it is a good effect, but the code has not been released to Joe Public. 

I'm interested in reproducing the crash, do I only need the gfx.wad and do you have a d/l link? 

You guys made me cry. Why won't anybody answer me? 

Have you tried right-clicking on the texture you want to change and using the Adjust Brightness control? You'll also find Remove Brites in there.

However, it tends to leave one pixel(255) as a fullbright. If that is a problem you will have to export that texture to a graphics program i.e. Photoshop, and adjust by hand. 

I prefer doodling around with Wally than TexMex -- a simple trick with Wally, just set brightness at -1 and contrast at +1 with the Q1 pallete loaded and it adjusts non palleted textures pretty accurately. You can even set up a wild cards that automates the process. I have never had a fullbright survive that sort or smack around before, so I say, give it a whirl -- as for TexMex, some swear by it, but I for one do not trust it. 

#3877 belongs in the drunk thread, but in case it is to any degree helpful . . . 

I believe this question was asked very recently and the answer(s) are posted above. Use TexMex. It has a function for adjusting the brightness of a texture once loaded ( and so converted to the quake palette ) which basically shifts each color up or down its respective color bar on the palette by however many places.

Two solutions were offered for removing fullbrights:
also using the Adjust Brightness dialogue, hit Remove Brites
or
go to View -> Preferences -> Workspace -> Color Conversion and uncheck Use Full Brites

Both of us who answered said that the other method didn't work properly. Try both and see which does. 

The second method for removing fullbrights only affects textures when they are imported, not if they are already in a wad. 

 

that was kinda weird 

Your question was answered at least twice, before you started whining about nobody answering you. 

I'm searching it for days now, having chequed mdl2map, dxf2map etc.

Is it possible to compile a bsp from a dxf file? Such as using a frame of a model to compile it to a bsp for bmodel.
It would be a nice sculpture.

otherwise I could construkt it again from polyhedrons, but then again I wondered;
is there a way to import dxf to Quark, or do I need another method for this? 

You could import .dxf into Qme, then save it as a .mdl, which you can then convert to .map in Mdl2map. And then compile the map as normal... if you wanted to?

But I don't know of a way to compile a .dfx file directly: the .dfx format is nothing like .map format. 

If you have Blender you can load the .dxf up and using this script

http://outpt.co.uk/files/USM%20Export%201.0.py

convert it to .ase format. Place the model in a Q3 Arena map as a misc_model with spawnflag 6. Compile with q3map2 http://www.shaderlab.com/ and then run Q3map2 again with the parameters -convert -format map and it will convert the mesh into brushes.

From there, use AquiRe's latest version of Txqbsp with the parameter -q2map (it will retain the q3 map level of accuracy - thnx AquiRe!) and you should have no problems, unless I missed a step.

A few things to note. The Nexuiz team wrote to ID about the legal status of using Q3map2 since they were using it for maps with a Quake based engine and not as the EULA intended, and Tom Hollenshead wrote back to them that for non commercial use, consider it it as GPLed until they formally release it under that license. 

I'm interested in reproducing the crash, do I only need the gfx.wad and do you have a d/l link?

Thanks for your generosity :) http://www.phait-accompli.com/q/s4/s4pak.zip 300 something KB.

One other problem (I hate posting all my problems in the midst of other's, but bear with me) -- I recently full VIS'd a map, which has no critical errors. It runs fine, I can quicksave and normal save. But when I quickload or normal load my point in the map - it gets stuck at "Loading" and I have to go to the console. In the console it says:

Loading game from e:\games\quake/id1/quick.sav...
couldn't spawn server maps/systkills:__0/__4____.bsp
couldn't load map

What sticks out here is the slashes - both \ and / is used... this problem occurs in FitzQuake 075, 080, and even WinQuake - and my friend experienced the same problem. I've never seen anything like it! You would think there is some map name problem, but the BSP is s4m1.bsp - and the title is something like:

Storage Facility E9

System 4
By Phait 

be the old "newlines in title" issue; take a look at my ToolTips document, Engine section. My engines can load such a savegame but the general solution is to remove the newlines from the title.

Thanks for the pak, I'll check it out. 

I'll look into the newlines stuff, that was one of my suspicions but didn't make sense as I've played maps w/ such titles and had no save/load problems. Thanks. 

Thanks for the help, sorry I missed it before. I guess I deserve a spanking or something. 

Reading the Q1Tooltips, I'm confused as your advice regarding the BSPInfo. I've extracted the .ENT file just fine, but: and then rebuild using qbsp with the "-onlyents" option.

How does the BSP update with the edited .ENT file? I tried qbsp -onlyents map.map map.bsp - but that didn't update it. 

I searched up the error, and found this in the Quake source:

/*
=============
Draw_TransPic
=============
*/
void Draw_TransPic (int x, int y, qpic_t *pic)
{
if (x < 0 || (unsigned)(x + pic->width) > vid.width || y < 0 ||
(unsigned)(y + pic->height) > vid.height)
{
Sys_Error ("Draw_TransPic: bad coordinates");
}

Draw_Pic (x, y, pic);
}


/*

That may help. Also, while testing this error again I clicked somewhere outside of the dialog box, I believe and got this error: Double Quake error: R_RenderView: called without enough stack - whic you can find in http://www.meowfishies.com/code/quakeforge-patches/files/r_main.c