Picture tell more:
https://drive.google.com/file/d/0BwxYkKdSD855M2lMQngtcWhiVUE/view?usp=sharing 

To be honest this would be interesting way to show secrets.. but I guess it is not intended or have something to do with how engine draws them? I'm using Quakespasm in this case. 

well that's uh.... not an intended feature. 

I remember when GL Quake was new, if you played a map that hadn't been vised specifically with transparent water, you would see a similar effect. Looking through water, doors and other entities were visible when they shouldn't be. 

Hmm.. it should be fully vised, no leaks etc. I use -level4. 

 

If it is 0.92.1 then it is up to date.

I tried to run it on Darkplaces too, and it worked just fine. In Quakespasm and Mark V (tested so far), I had these drawing issues. 

yes i use test level 4. How can i change the level? how will it affect the compile? i have not used detail entitys since im still a beginner. thanks for that tip!

im taking a small break from my main project because its getting too large and there are so many areas im not happy with. there will still be large outdoor areas but i will make them smaller. 

light.exe

-fast

easiest way, less calculate time.

-extra

Calculate extra samples (2x2) and average the results for smoother shadows.

-extra4

Calculate even more samples (4x4) and average the results for smoother shadows. 

I ment vis.exe. 

Quick question, i downloaded some skyboxes and renamed them from .pk3 to .tga
(https://www.quaddicted.com/webarchive/kell.quaddicted.com/skyboxes.html)

i placed the skybos in id1/gfx/env

in trenchbroom i gave world entity "sky" "sky-dragonheart_"

and nothing happened. What went wrong? 

Verify the name of the actual skybox files. Is it "sky-dragonheart_" or just "dragonheart_" 

http://imgur.com/a/PTGUX 

I think there should be the 6 cube sides for the skybox files.

Like sky-dragonheartup_
"""down_
"""lf_

Can you open the pak and see if those files are contained? 

i dont know how to extract pk3.
can you send me a skybox file that i can test? 

i downloaded the skyboxes from quaddicted

https://www.quaddicted.com/webarchive/kell.quaddicted.com/skyboxes.html

i think they should be 6 sided 

is there a texture that i have to give to a brush so i can see the skybox? like sky4 

#17683 - You should be able to open it with any zip extractor, if I remember correctly;

#17684 - Due to the inordinate amount of work to compose 49 separate downloads, these skyboxes are currently only available in a single download as The Kothic Skybox Compilation
===> The Kothic Skybox Compilation

#17685 - you have to use sky texture; 

That's probably caused by a lack of sorting by distance for entities with transparency.

FitzQuake 0.85 draws entities sequentially. DarkPlaces likely sorts everything by distance.

I might rewire transparent entities to draw by distance in Mark V, but I've more focused on a mirrors on func_illusionary request for pulsar ..

And tuning some optional effects video and updating the Mac build. 

The only important VIS options are -fast for a quick and inaccurate test compile, and -level 4 for a slow(er) and accurate final compile. 

you have to use sky texture;

What is a sky texture? i used both sk1 and sky4 and both of them wont display the skybox 

i got it to work now! :)
I copied a skybox from my Arcane dimensions folder and placed in my id1/gf/env folder and it doesnt matter what sky texture i use! im happy with the result now :)))) 

I created a square room, I placed a pillar directly in the center, I set sunlight mangle to 270 -45 0

This way the sun in relation to my Top view in JACK is at the top(centered). I placed the player start in relation to the Top view at the bottom(centered).

Now when I load the map the pillar casts a shadow directly towards me, correct. Looking right, the wall has a shadow at a 45 degree angle down, correct.

But looking left the wall is completely dark. It doesn't match the right side wall which I thought it would.

What is going on?

If there is a sunlight basics link(besides ericw's descriptions) please post it, thanks. 

https://shoresofnis.wordpress.com/guides/lighting-basics/

It states "�_sun_mangle� - This has the same format as �mangle� on spot lights, �Direction, Pitch, x�, which way the sun is shining. (Not the position the sun is in)"

So my question is, how do I know where the position of the sun is? 

The sun doesn't have a position like a regular light entity, it's a "distant light source" so wherever you are in the map, the direction vector to the sun is the same.

So what happens is from each lightmap sample in the map, the tool traces a line in the direction to the sun, and checks if it hits a sky face.

With the "yaw" component of mangle at 270 I would expect 3 walls to be lit up.. but with light coming in perpendicular to two of the walls, the value of "anglescale" will determine whether they receive any light, if "anglescale" is 1, those walls perpendicular to the sunlight direction will be dark.

There's also the possiblity of a bug of course. mind posting a screenshot?