Func_Msgboard: Mapping Help

Posted by metlslime on 2002/12/23 18:31:29

This is the place to ask about mapping problems, techniques, and bug fixing, and pretty much anything else you want to do in the level editor.

For questions about coding, check out the Coding Help thread: https://www.celephais.net/board/view_thread.php?id=60097

First | Previous | Next | Last

#17660 posted by Naitelveni on 2016/12/01 13:23:08

i have a huge outdoor area, i dont box my map and i do have some detail.

what about the void bug?

#17661 posted by Mugwump on 2016/12/01 13:25:05

It really shouldnt be taking hours to compile.
If his computer is antediluvian, it might. What system are you working on, Naite?

#17662 posted by mjb on 2016/12/01 13:25:50

I am not sure about your issue with the void but that outdoor area may be the cause or at least a large factor of your compile times. Try to find more non-essential brushes to make into func_detail brushes. Depending on how huge, you may have to consider closing in that outdoor section or deal with the large compile.

#17663 posted by Naitelveni on 2016/12/01 13:40:09

I have a 2013 imac 2.9 ghz with 8gb ram.
Os is Windows 8.

i have to make my outdoor area smaller. :/
its too bad that big areas affect the compiling time so dramatically.

Func Details?

#17664 posted by Newhouse on 2016/12/01 13:48:55

Since I'm bad at using words when asking something:
https://drive.google.com/file/d/0BwxYkKdSD855akRteldicXhqTGc/view?usp=sharing

Sacrifice

#17665 posted by mjb on 2016/12/01 13:49:59

Are you using -level 4 for your VIS? You could try just a normal VIS just to see.

You could also share your .map file for others to analyze and see what could be done.

That's entirely up to you though!

#17666 posted by Mugwump on 2016/12/01 13:51:15

Or if you can cope with long compiling times, you might want to consider going with it: it's not often that we can enjoy large outdoors in Quake. I sure would like to see more of these.

NewDetail

#17667 posted by mjb on 2016/12/01 13:59:30

NewHouse,

Yes that is a good example of using func_details.

Another way to see is if you select all of your func_details and hide them...is your map still able to fully VIS?

Func_detail

#17668 posted by khreathor on 2016/12/01 14:40:35

It's just ignored by VIS, but other than that it behaves as a normal brush, so collision etc. works the same.
Important thing is to not use them as main walls closing your map - VIS will get rekt this way.

Thank You* Another Question About Func_Illusionary

#17669 posted by Newhouse on 2016/12/01 15:07:27

Picture tell more:
https://drive.google.com/file/d/0BwxYkKdSD855M2lMQngtcWhiVUE/view?usp=sharing

#17670 posted by Newhouse on 2016/12/01 15:09:35

To be honest this would be interesting way to show secrets.. but I guess it is not intended or have something to do with how engine draws them? I'm using Quakespasm in this case.

#17671 posted by Shamblernaut on 2016/12/01 15:31:52

well that's uh.... not an intended feature.

#17672 posted by Rick on 2016/12/01 16:16:40

I remember when GL Quake was new, if you played a map that hadn't been vised specifically with transparent water, you would see a similar effect. Looking through water, doors and other entities were visible when they shouldn't be.

#17673 posted by Newhouse on 2016/12/01 16:30:25

Hmm.. it should be fully vised, no leaks etc. I use -level4.

Is Your QuakeSpasm Up-to-date?

#17674 posted by Mugwump on 2016/12/01 16:36:28

#17675 posted by Newhouse on 2016/12/01 16:48:39

If it is 0.92.1 then it is up to date.

I tried to run it on Darkplaces too, and it worked just fine. In Quakespasm and Mark V (tested so far), I had these drawing issues.

#17676 posted by Naitelveni on 2016/12/03 00:48:57

yes i use test level 4. How can i change the level? how will it affect the compile? i have not used detail entitys since im still a beginner. thanks for that tip!

im taking a small break from my main project because its getting too large and there are so many areas im not happy with. there will still be large outdoor areas but i will make them smaller.

Easy

#17677 posted by madfox on 2016/12/03 00:58:27

light.exe

-fast

easiest way, less calculate time.

-extra

Calculate extra samples (2x2) and average the results for smoother shadows.

-extra4

Calculate even more samples (4x4) and average the results for smoother shadows.

Oops

#17678 posted by madfox on 2016/12/03 01:01:28

I ment vis.exe.

#17679 posted by Naitelveni on 2016/12/03 01:08:01

Quick question, i downloaded some skyboxes and renamed them from .pk3 to .tga
(https://www.quaddicted.com/webarchive/kell.quaddicted.com/skyboxes.html)

i placed the skybos in id1/gfx/env

in trenchbroom i gave world entity "sky" "sky-dragonheart_"

and nothing happened. What went wrong?

Name

#17680 posted by mjb on 2016/12/03 01:43:47

Verify the name of the actual skybox files. Is it "sky-dragonheart_" or just "dragonheart_"

#17681 posted by Naitelveni on 2016/12/03 02:10:39

http://imgur.com/a/PTGUX

Directions

#17682 posted by mjb on 2016/12/03 02:13:58

I think there should be the 6 cube sides for the skybox files.

Like sky-dragonheartup_
"""down_
"""lf_

Can you open the pak and see if those files are contained?

#17683 posted by Naitelveni on 2016/12/03 02:22:45

i dont know how to extract pk3.
can you send me a skybox file that i can test?

#17684 posted by Naitelveni on 2016/12/03 02:23:39

i downloaded the skyboxes from quaddicted

https://www.quaddicted.com/webarchive/kell.quaddicted.com/skyboxes.html

i think they should be 6 sided

First | Previous | Next | Last

You must be logged in to post in this thread.